General Description
The MAX7313 I
2
CTM-compatible serial interfaced
peripheral provides microprocessors with 16 I/O ports.
Each I/O port can be individually configured as either
an open-drain current-sinking output rated at 50mA and
5.5V, or a logic input with transition detection. A 17th
port can be used for transition detection interrupt, or as
a general-purpose output. The outputs are capable of
driving LEDs, or providing logic outputs with external
resistive pullup up to 5.5V.
PWM current drive is integrated with 8 bits of control.
Four bits are global control and apply to all LED outputs
to provide coarse adjustment of current from fully off to
fully on with 14 intensity steps. Each output then has
individual 4-bit control, which further divides the global-
ly set current into 16 more steps. Alternatively, the cur-
rent control can be configured as a single 8-bit control
that sets all outputs at once.
The MAX7313 is pin and software compatible with the
MAX7311, PCA9535, and PCA9555.
Each output has independent blink timing with two blink
phases. All LEDs can be individually set to be on or off
during either blink phase, or to ignore the blink control.
The blink period is controlled by a register.
The MAX7313 supports hot insertion. All port pins, the
INT output, SDA, SCL, and the slave-address inputs
ADO-2 remain high impedance in power-down (V+ =0V)
with up to 6V asserted upon them.
The MAX7313 is controlled through the 2-wire
I
2
C/SMBus serial interface, and can be configured to
any one of 64 I
2
C addresses.
Applications
LCD Backlights
LED Status Indication
Portable Equipment
Keypad Backlights
RGB LED Drivers
Notebook Computers
Features
400kbs, 2-Wire Serial Interface, 5.5V Tolerant
2V to 3.6V Operation
Overall 8-Bit PWM LED Intensity Control
Global 16-Step Intensity Control
Individual 16-Step Intensity Controls
Two-Phase LED Blinking
High Output Current (50mA max Per Port)
Outputs are 5.5V-Rated Open Drain
Supports Hot Insertion
Inputs are Overvoltage Protected to 5.5V
Transition Detection with Interrupt Output
1.2A (typ), 3.6A (max) Standby Current
Small 4mm x 4mm Thin QFN Package
-40C to +125C Temperature Range
All Ports Can Be Configured as Inputs or Outputs
MAX7313
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
________________________________________________________________ Maxim Integrated Products
1
TOP VIEW
THIN QFN
MAX7313ATG
19
20
21
22
1
2
3
4
5
6
18
17
16
15
14
13
23
24
12
11
10
9
8
7
SCL
V+
SDA
INT/O16
AD2
P0
P1
P2
P3
P4
P5
AD0
P15
P13
P12
P11
AD1
P10
P8
P9
GND
P6
P7
P14
Pin Configurations
19-3059; Rev 4; 4/05
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.
Ordering Information
PART
TEMP RANGE
PIN-
PACKAGE
PKG
CODE
MAX7313ATG
-40
C to +125C
24 Thin QFN
4mm x 4mm
x 0.8mm
T2444-4
MAX7313AEG
-40
C to +125C 24 QSOP
--
Pin Configurations continued at end of data sheet.
Typical Application Circuit appears at end of data sheet.
Purchase of I
2
C components of Maxim Integrated Products, Inc.,
or one of its sublicensed Associated Companies, conveys a
license under the Philips I
2
C Patent Rights to use these compo-
nents in an I
2
C system, provided that the system conforms to the
I
2
C Standard Specification as defined by Philips.
MAX7313
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltage (with respect to GND)
V+ .............................................................................-0.3V to +4V
SCL, SDA, AD0, AD1, AD2, P0P15 ........................-0.3V to +6V
INT/O16 ....................................................................-0.3V to +8V
DC Current on P0P15, INT/O16 ........................................55mA
DC Current on SDA.............................................................10mA
Maximum GND Current ....................................................350mA
Continuous Power Dissipation (T
A
= +70C)
24-Pin QSOP (derate 9.5mW/C over +70C)..............761mW
24-Pin QFN (derate 20.8mW/C over +70C) ............1666mW
Operating Temperature Range (TMIN to TMAX)-40C to +125C
Junction Temperature ......................................................+150C
Storage Temperature Range .............................-65C to +150C
Lead Temperature (soldering, 10s) .................................+300C
ELECTRICAL CHARACTERISTICS
(Typical Operating Circuit, V+ = 2V to 3.6V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at V+ = 3.3V, T
A
= +25C.)
(Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Supply Voltage
V+
2
3.6
V
Output Load External Supply
Voltage
V
EXT
0
5.5
V
T
A
= +25C
1.2
2.3
T
A
= -40C to +85C
2.8
Standby Current
(Interface Idle, PWM Disabled)
I
+
S C L and S D A at V + ; other
d i g i tal i np uts at V + or GN D ;
P WM i ntensi ty contr ol d i sab l ed
T
A
= T
MIN
to T
MAX
3.6
A
T
A
= +25C
8.5
15.1
T
A
= -40C to +85C
16.5
Supply Current
(Interface Idle, PWM Enabled)
I
+
S C L and S D A at V + ; other
d i g i tal i np uts at V + or GN D ;
P WM i ntensi ty contr ol enab l ed
T
A
= T
MIN
to T
MAX
17.2
A
T
A
= +25C
50
95.3
T
A
= -40C to +85C
99.2
Supply Current
(Interface Running, PWM
Disabled)
I
+
f
SCL
= 400kHz; other digital
inputs at V+ or GND; PWM
intensity control disabled
T
A
= T
MIN
to T
MAX
102.4
A
T
A
= +25C
57
110.2
T
A
= -40C to +85C
117.4
Supply Current
(Interface Running, PWM
Enabled)
I
+
f
SCL
= 400kHz; other digital
inputs at V+ or GND; PWM
intensity control enabled
T
A
= T
MIN
to T
MAX
122.1
A
Input High Voltage
SDA, SCL, AD0, AD1, AD2,
P0P15
V
IH
0.7
V+
V
Input Low Voltage
SDA, SCL, AD0, AD1, AD2,
P0P15
V
IL
0.3
V+
V
Input Leakage Current
SDA, SCL, AD0, AD1, AD2,
P0P15
I
IH
, I
IL
Input = GND or V+
-0.2
+0.2
A
Input Capacitance
SDA, SCL, AD0, AD1, AD2,
P0P15
8
pF
MAX7313
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
_______________________________________________________________________________________
3
ELECTRICAL CHARACTERISTICS (continued)
(Typical Operating Circuit, V+ = 2V to 3.6V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at V+ = 3.3V, T
A
= + 25C.)
(Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
T
A
= +25C
0.15
0.26
T
A
= -40C to +85C
0.3
V+ = 2V, I
SINK
= 20mA
T
A
= T
MIN
to T
MAX
0.32
T
A
= +25C
0.13
0.23
T
A
= -40C to +85C
0.26
V+ = 2.5V, I
SINK
= 20mA
T
A
= T
MIN
to T
MAX
0.28
T
A
= +25C
0.12
0.23
T
A
= -40C to +85C
0.24
Output Low Voltage
P0P15, INT/O16
V
OL
V+ = 3.3V, I
SINK
= 20mA
T
A
= T
MIN
to T
MAX
0.26
V
Output Low-Voltage SDA
V
OLSDA
I
SINK
= 6mA
0.4
V
PWM Clock Frequency
f
PWM
32
kHz
TIMING CHARACTERISTICS
(Typical Operating Circuit, V+ = 2V to 3.6V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at V+ = 3.3V, T
A
= +25C.)
(Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Serial Clock Frequency
f
SCL
400
kHz
Bus Free Time Between a STOP and a START
Condition
t
BUF
1.3
s
Hold Time, Repeated START Condition
t
HD, STA
0.6
s
Repeated START Condition Setup Time
t
SU, STA
0.6
s
STOP Condition Setup Time
t
SU, STO
0.6
s
Data Hold Time
t
HD, DAT
(Note 2)
0.9
s
Data Setup Time
t
SU, DAT
180
ns
SCL Clock Low Period
t
LOW
1.3
s
SCL Clock High Period
t
HIGH
0.7
s
Rise Time of Both SDA and SCL Signals, Receiving
t
R
(Notes 3, 4)
20 +
0.1C
b
300
ns
Fall Time of Both SDA and SCL Signals, Receiving
t
F
(Notes 3, 4)
20 +
0.1C
b
300
ns
Fall Time of SDA Transmitting
t
F.TX
(Notes 2, 3, 5)
20 +
0.1C
b
250
ns
Pulse Width of Spike Suppressed
t
SP
(Notes 2, 6)
50
ns
Capacitive Load for Each Bus Line
C
b
(Notes 2, 3)
400
pF
MAX7313
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
4
_______________________________________________________________________________________
TIMING CHARACTERISTICS (continued)
(Typical Operating Circuit, V+ = 2V to 3.6V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at V+ = 3.3V, T
A
= +25C.)
(Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Interrupt Valid
t
IV
Figure 10
6.5
s
Interrupt Reset
t
IR
Figure 10
1
s
Output Data Valid
t
DV
Figure 10
5
s
Input Data Setup Time
t
DS
Figure 10
100
ns
Input Data Hold Time
t
DH
Figure 10
1
s
Note 1: All parameters tested at T
A
= +25C. Specifications over temperature are guaranteed by design.
Note 2: A master device must provide a hold time of at least 300ns for the SDA signal (referred to V
IL
of the SCL signal) to bridge
the undefined region of SCL's falling edge.
Note 3: Guaranteed by design.
Note 4: C
b
= total capacitance of one bus line in pF. t
R
and t
F
measured between 0.3 x V
DD
and 0.7 x V
DD
.
Note 5: I
SINK
6mA. C
b
= total capacitance of one bus line in pF. t
R
and t
F
measured between 0.3 x V
DD
and 0.7 x V
DD
.
Note 6: Input filters on the SDA and SCL inputs suppress noise spikes less than 50ns.
STANDBY CURRENT vs. TEMPERATURE
MAX7313 toc01
TEMPERATURE (
C)
STANDBY CURRENT (
A)
110
95
65 80
-10 5
20 35 50
-25
1
2
3
4
5
6
7
8
9
10
0
-40
125
V+ = 3.6V
PWM ENABLED
V+ = 2.7V
PWM ENABLED
V+ = 2V
PWM DISABLED
V+ = 2.7V
PWM DISABLED
V+ = 3.6V
PWM
DISABLED
V+ = 2V
PWM ENABLED
SUPPLY CURRENT vs. TEMPERATURE
(PWM DISABLED; f
SCL
= 400kHz)
MAX7313 toc02
TEMPERATURE (
C)
SUPPLY CURRENT (
A)
110
95
65 80
-10 5
20 35 50
-25
10
20
30
40
50
60
70
0
-40
125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
5
10
15
20
25
30
35
40
45
50
55
60
65
70
0
SUPPLY CURRENT vs. TEMPERATURE
(PWM ENABLED; f
SCL
= 400kHz)
MAX7313 toc03
TEMPERATURE (
C)
SUPPLY CURRENT (
A)
110
95
65 80
-10 5
20 35 50
-25
-40
125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
__________________________________________Typical Operating Characteristics
(T
A
= +25C, unless otherwise noted.)
MAX7313
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
_______________________________________________________________________________________
5
PORT OUTPUT LOW VOLTAGE WITH 50mA
LOAD CURRENT vs. TEMPERATURE
PORT OUTPUT LOW VOLTAGE V
OL
(V)
0.1
0.2
0.3
0.4
0.5
0.6
0
MAX7313 toc04
TEMPERATURE (
C)
110
95
65 80
-10 5
20 35 50
-25
-40
125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
PORT OUTPUT LOW VOLTAGE WITH 20mA
LOAD CURRENT vs. TEMPERATURE
MAX7313 toc05
TEMPERATURE (
C)
PORT OUTPUT LOW VOLTAGE V
OL
(V)
110
95
80
65
50
35
20
5
-10
-25
0.1
0.2
0.3
0.4
0.5
0.6
0
-40
125
ALL OUTPUTS LOADED
V+ = 3.6V
V+ = 2.7V
V+ = 2V
PWM CLOCK FREQUENCY
vs. TEMPERATURE
MAX7313 toc06
TEMPERATURE (
C)
PWM CLOCK FREQUENCY
110
95
80
65
50
35
20
5
-10
-25
0.950
1.000
1.050
0.900
0.925
0.975
1.025
-40
125
V+ = 3.6V
V+ = 2V
V+ = 2.7V
NORMALIZED TO V+ = 3.3V, T
A
= +25
C
SCOPE SHOT OF 2 OUTPUT PORTS
MAX7313 toc07
2ms/div
OUTPUT 1
2V/div
OUTPUT 2
2V/div
MASTER INTENSITY SET TO 1/15
OUTPUT 1 INDIVIDUAL INTENSITY
SET TO 1/16
OUTPUT 2 INDIVIDUAL INTENSITY
SET TO 15/16
SCOPE SHOT OF 2 OUTPUT PORTS
MAX7313 toc08
2ms/div
OUTPUT 1
2V/div
OUTPUT 2
2V/div
OUTPUT 1 INDIVIDUAL INTENSITY
SET TO 1/16
MASTER INTENSITY SET TO 14/15
OUTPUT 2 INDIVIDUAL INTENSITY
SET TO 14/15
MAX7313 toc09
SINK CURRENT vs. V
OL
SINK CURRENT (mA)
V
OL
(V)
50
40
30
20
10
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0
0
V+ = 2V
V+ = 2.7V
ONLY ONE OUTPUT LOADED
V+ = 3.3V
V+ = 3.6V
Typical Operating Characteristics (continued)
(T
A
= +25C, unless otherwise noted.)
PDF 
ZIP