MAD00064AEM
MN101E31G
Type
MN101E31G
MN101EF31G
Internal ROM type
Mask ROM
FLASH
ROM (byte)
128K
RAM (byte)
4K
Package (Lead-free)
LQFP080-P-1414A (Under development)
Minimum Instruction
Execution Time
50 ns (at 2.2 V to 5.5 V, 20 MHz)
* at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used
50 ns (at 2.2 V to 5.5 V, 20 MHz)
Interrupts
6 external interrupts, 25 internal interrupts
RESET, Watchdog, External 0 to 4, Timer 0 to 4, Timer 6, Timer 7 (2 systems), Timer 8 (2 systems), Time base, Serial 0 (2 systems),
Serial1 (2 systems), Serial 2 (2 systems), Serial 3 (2 systems), Serial 4, Serial 5, A/ conversion fi nish, Automatic transfer, Key
interrupts
Timer Counter
Timer counter 0 : 8-bit 1
(timer pulse output, event count, added pulse (2-bit) system PWM output, generation of remote control carrier, simple
pulse measurement, real time output control)
Timer counter 1 : 8-bit 1
(timer pulse output, event count, 16-bit cascade connected (timer 0, 1) timer synchronous output event)
Timer counter 2 : 8-bit 1
(timer pulse output, event count, added pulse (2-bit) system PWM output, simple pulse measurement, 24-bit cascade
connected (timer 0, 1, 2), timer synchronous output event, real timer output control)
Timer counter 3 : 8-bit 1
(timer pulse output, event count, generation of remote control carrier, 16-bit cascade connected (timer 2, 3), 32-bit
cascade connected (timer 0, 1, 2, 3))
Timer counter 4 : 8-bit 1
(timer pulse output, added pulse (2-bit) system PWM output, event count, serial transfer clock, simple pulse
measurement)
Timer counter 6 : 8-bit free run timer, time base timer
Timer counter 7 : 16-bit 1
(timer pulse output, event count, High accuracy PWM, High performance IGBT output (cycle/duty continuous variable)
timer synchronous output event, input capture (Both edge available), real timer output control), double buffer compare
register
Timer counter 8 : 16-bit 1
(timer pulse output, event count, High accuracy PWM output (cycle/duty continuous variable) pulse width measurement,
input capture (Both edge available), 32-bit cascade connected (Timer 7 , 8), 32-bitPWM output, synchronous output
event), double buffer compare register
Timer counter A : 8-bit 1 (event count, Serial transfer clock timer, clock for function (timer, serial, LCD))
Watchdog timer
Serial interface
Serial 0 ~ 3 : UART (full duplex) / synchronous 1
Serial : multi master IC / synchronous 1
Serial 5 : IC slave 1
DMA controller
1 systems (External request/internal event request/software request maximum transfer cycles are 255)
I/O Pins
I/O
70
common use, Specifi ed pull-up/pull-down resistor available, Input/output selectable (bit-unit)
MAD00064AEM
MN101E31G
A/D converter
10-bit 12-ch.
Display control function
LCD
55 segments 4 commons (static, 1/2, 1/3, 1/4 duty) 1/3 bias
Usable if VLC1 VDD
Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
ROM Correction
Correcting address designation : up to 7 addresses possible
Development tools
In-circuit Emulator
PX-ICE101E PRBV101E31- LQFP080-P-1414A (Under development)
Pin Assignment
P73, SDA5A, NRE, SEG
8
P72, SBT2A, NWE, SEG
9
P71, SBI2A, RXD2A, A7, SEG10
P70, SBO2A, TXD2A, A6, SEG
1
1
P67, SBT4A, SCL4A, A5, SEG12
P66, SBO4A, SDA4A, A4, SEG13
P65, SBI4A, A3, SEG14
P64, TM4IOB, A2, SEG15
P63, TM3IOB, A1, SEG16
P62, TM1IOB, A0, SEG17
P61, SEG1
8
P50, KEY0, D0, SEG19
P51, SBI0A, RXD0A, KEY1, D1, SEG20
P52, SBT0A, KEY2, D2, SEG2
1
P53, BUZZERA, KEY3, D3, SEG2
2
P54, NBUZZERA, KEY4, D4, SEG23
P55, KEY5, D5, SEG24
P56, KEY6, D6, SEG25
P57, KEY7, D7, SEG26
P47, SCL5B, SEG27
P74, SCL5A, NCS, SEG7
P75, SBO1B, TXD1B, A8, SEG6
P76, SBI1B, RXD1B, A9, SEG5
P77, SBT1B, A10, SEG4
P80, SDO0, A11, SEG3
P81, SDO1, A12, SEG2
P82, SDO2, A13, SEG1
P83, SDO3, A14, SEG0
P84, SDO4, A15, COM0
P85, SDO5, A16, COM1
P86, SDO6, A17, COM2
P87, SDO7, A18, COM3
P92, A19, VLC3
P93, NDK, VLC2
P94, SYSCLK, VLC1
P95
PB3, AN11
PB2, AN10
PB1, AN9
PB0, AN8
P46, SDA5B, SEG28
P45, SBT0B, SEG29
P44, SBI0B, RXD0B, SEG30
P43, SBO0B, TXD0B, SEG31
P35, SBI4B, SEG32
P34, SBT4B, SCL4B, SEG33
P33, SBO4B, SDA4B, SEG34
P10, TM0IOC, RMOUTC, SEG35
P24, IRQ4, SEG36
P23, IRQ3, SEG37
P22, IRQ2, SEG38
P21, IRQ1, ACZ1, SEG39
P20, IRQ0, ACZ0, SEG40
P06, LED6
P05, LED5
P04, LED4
P03, LED3, TM0IOB, TM2IOB, RMOUTB
P02, LED2, SBT1A
P01, LED1, TM8IOB, SBO1A, TXD1A
P00, LED0, TM7IOB, SBI1A, RXD1A
P
A
0, AN0, TM0IOA, RMOUT
A
P
A
1, AN1, TM1IOA
P
A
2, AN2, TM2IOA
P
A
3, AN3, TM3IOA
P
A
4, AN4, TM4IOA
P
A
5, AN5, TM7IOA
P
A
6, AN6, TM8IOA
P
A7, AN
7
VREF
+
MMOD
A
T
RS
T
P27, NRST
P91, XO
P90, XI
VS
S
OSC1
OSC2
V
D
D
5
V
D
D
1
8
DMO
D
1
2
3
4
5
6
7
8
9
10
1
1
12
13
14
15
16
17
18
19
20
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
MN101E31G
LQFP080-P-1414A
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd. Industrial Co., Ltd.
PDF 
ZIP