SLP-9117E-51
No.6061 1/4
Features
GaAsP red LED
3.1mm, U-cut type lamp
Light red epoxy resin package type
The insertion which made it stick to PCB is possible
High luminous intensity, high reliability and long life
Application : for the general public welfare
Absolute Maximum Ratings at Ta=25
C (as per JIS C 7032)
Parameter
Symbol
Rating
Unit
Forward Current
*1
I
F
25
mA
Pulse Forward Current
*2
I
FP
100
mA
Reverse Voltage
V
R
3
V
Power Dissipation
P
D
70
mW
Operating Temperature
Topr
--25 to +80
C
Storage Temperature
Tstg
--30 to +85
C
Soldering Temperature
*3
Tsol
260
C
*1
See forward current derating
*2
Pulse width = Max. 10ms Duty ratio = Max. 1 / 10
*3
Max. 5sec., Lead soldering condition : Min. 1.6mm from case (used 1.6mm'ts PCB)
Electrical / Optical Characteristics at Ta=25
C
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Unit
Foward Voltage
V
F
I
F
= 20mA
1.7
2.1
2.8
V
Reverse Current
I
R
V
R
= 3V
--
--
10
A
Luminous Intensity
*4
I
V
I
F
= 20mA
4.2
8
--
mcd
Peak Wave length
P
I
F
= 20mA
--
630
--
nm
Line Half Width
I
F
= 20mA
--
40
--
nm
Capacitance
C
O
V
O
= 0
F = 1MHz
--
40
--
pF
Response Time
t
--
--
90
--
ns
*4
Luminous Intensity is measured by J-16 (SONY TEKTRONIX) of which our office possess.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
Ordering number : EN6061
SLP-9117E-51
Infrared LED
3.1mm red contact type LED lamp
(U-cut version)
52699 GI, (MI)
1.55
2
4.5
0.5
9.2
0.5
0.8 max
28.5
1
4.4
3.1
3
Anode
Cathode
2.5
(1.5)
2 max (not soldered)
2.2
1
4.2
R0
.5
0.5
0.4
0.4
Note : Material -- lron
Coating -- Solder
Lead center off :
0.4
Unit :
mm
SLP-9117E-51
No.6061 2/4
Typical Characteristics
These shows the electrical and optical characteristics of this products, and not assure this dispersive contents.
CAUTION
Forward Current vs. Forward Voltage
F
orw
ard Current (mA)
Forward Voltage (V)
Intensity vs. Temperature (IF : constant)
Relati
v
e
Intensity
Temperature (
C)
Intensity vs. Current
Relati
v
e
Intensity
Forward Current (mA)
Spectrum
Relati
v
e
Intensity
Wave Length (nm)
Forward Current Derating (Abusolute Maximum Rating)
F
orw
ard Current (mA)
Temperature (
C)
Directivity
30
20
10
5
3
2
1
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
1.5
1.0
0.5
--40
--20
0
20
40
60
80
100
1
2
5
10
20
50
100 200
500
550
600
650
700
0
10
30
20
40
50
60
70
80
90
100
10
5
2
1
0.5
0.2
0.1
1.0
0.5
0
35
30
25
20
15
10
5
0
90
80
70
60
50
40
30
20
10
0
90
80
70
60
50
40
30
20
10
1.0
0.1
0.5
SLP-9117E-51
No.6061 3/4
(1) Bending a lead should avoid not to cause chip deterioration or so. When bending is necessary, care must be taken
considering the following points :
q Bending a lead must be done before soldering.
w Bending a lead must be done in the states of fixing a lead tight and applying no stress on the resin part; otherwise it
may cause troubles such as gold wire breaking.
e A lead must be bent at intervals of 1.6mm from the edge of the resin part.
r Do not bend the same portion of lead more than twice.
(2) Setting a product by a tool such as holder should avoid. When necessary, no stress should be applied to the resin part and
lead by sufficient considerations on dimension tolerance, thermal expansion, thermal contraction of holder, product and
circuit board.
(3) The hole pitch of a circuit board must fit to its lead pitch.
(4) When soldering, care must be taken considering the following points :
q Do not heat a product under any stress (ex. : twist) to leads.
w Do not heat (by soldering, for example) a product in the states of being forced to the resin part.
(5) Do not use the flux containing chlorine which may cause corrosion of lead and washing is preferable. When washing is
necessary, avoid washing the whole product and wash only the needed part under the following conditions.
Chemicals : Methyl alcohol
Temperature : 45
C max.
Time : 30sec. max.
PRECAUTIONS
SLP-9117E-51
No.6061 4/4
CAUTION
1. No products described or contained herein are intended for use in surgical implants, life-support systems,
aerospace equipment, nuclear power control systems, vehicles, disaster / crime-prevention equipment or
the like, and the failure of which may directly or indirectly cause injury, death or property loss.
2. Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1) Accept full responsibility and indemnify and defend SANYO ELECTRIC CO.,LTD., it's affiliates,
subsidiaries and distributors or any of their officers and employees, jointly and severally, against any
and all claims and litigation and all damages, costs and expenses associated with such use.
2) Not impose any responsibility for any fault or negligence which may be cited in any such claim or
litigation on SANYO ELECTRIC CO., LTD., it's affiliates, subsidiaries and distributors or any of
their officers and employees jointly or severally.
3. Information (including circuit diagrams and circuit parameters) disclosed herein is for example only; it is not
guaranteed for mass production, SANYO believes the information disclosed herein is accurate and reliable,
but no guarantees are made or implied regarding it's use or any infringements of intellectual property rights
or other rights of third parties.
Precautionary instructions in handling gallium arsenic products
Special precautions must be taken in handling this product because it contains, gallium arsenic, which is
designated as a toxic substance by law. Be sure to adhere strictly to all applicable laws and regulations
enacted for this substance, particularly when it comes to disposal.
Manufactured by ;
Tottori SANYO Electric Co., Ltd.
LED Division
5-318, Tachikawa-cho, Tottori City, 680-8634 Japan
TEL: +81-857-21-2137 FAX: +81-857-21-2161
PS
PDF 
ZIP